Advanced Equipment
We are equipped with advanced Japanese-made internal mixers, two-roll mixers and reactors. The rubber products plant has rotary vulcanizers, presses, extruders and other special equipment.
Production Capacity
We have three FKM material production lines: one for premixes, one for black compounds, and one for color compounds. Our total production capacity of fluororubber compounds and polymers is up to 4,800 tons per year.
Quality Control
We adheres to strict quality inspection standards from raw material procurement to final product delivery, including GB/T, HG/T, ASTM, SAE, DIN, ISO, TL, BMW, and GM.
Customized service
We provide comprehensive customized solutions, deeply understand customers' specific requirements for hardness, color, application areas and physical properties, and ensure that the products fully meet customer needs.
We offer custom AEM rubber manufacturing solutions to meet your needs. Key customizable options:
● Hardness
● Color
● Size
● Shape
● Temperature range
● Chemical resistance
● Tensile strength
● Elongation
● Surface treatment
|
Est Project |
Unit |
Test method |
Value |
|
Hardness |
Shore A |
ASTM D-2240 |
68 |
|
Tensile strength |
MPa |
ASTM D-412 |
11.76 |
|
Elongation |
% |
ASTM D-412 |
241.2 |
|
Tear strength |
N/mm |
ASTM D-624 |
32.1 |
|
Specific gravity |
g/cm3 |
--- |
1.31 |
AEM Compound
Ethylene acrylate rubber (AEM) has good resistance to lubricating oils, but we often see some standards citing reference oils as test oils instead of using actual lubricating oils for testing. Based on the 50% reduction in elongation at break, AEM can be used continuously for 18 months at 120°C and for 6 weeks at 170°C. The heat aging resistance of AEM is much better than that of chlorosulfonated polyethylene rubber (CSM) and NBR.
Temperature Resistance:
AEM rubber has an excellent resistance to high temperatures, withstanding continuous exposure to temperatures up to 150°C (302°F) and intermittent exposure up to 175°C (347°F). It also retains its flexibility and performance at low temperatures, typically down to -40°C (-40°F).
Chemical Resistance:
AEM rubber offers good resistance to oils, fuels, and various chemicals, including automotive fluids like engine oil, transmission fluid, and coolant. However, it is not suitable for exposure to strong acids, alkalis, or polar solvents.
Weathering and Ozone Resistance:
AEM rubber has strong resistance to environmental factors such as UV rays, ozone, and oxidation, which can cause other elastomers to degrade over time.
Mechanical Properties:
AEM rubber exhibits good tensile strength, elongation, and compression set resistance. This means it can maintain its shape and integrity under mechanical stress, making it suitable for use in dynamic applications.
Electrical Properties:
AEM rubber has moderate electrical insulating properties, which can be useful in certain applications like wire and cable jackets.
Low Permeability:
AEM rubber has low permeability to gases, which makes it suitable for applications where sealing against gas leakage is essential.
Flammability:
AEM rubber is inherently flame-resistant, meaning it has a low tendency to support combustion.
Temperature: Storage temperature must be between 59°F (15°C) and 100°F (38°C).
Humidity: Relative Humidity (RH) must be less than 75% unless stored in sealed moisture proof bags.
Light: Material must be protected from direct sunlight and/or intense artificial light having U.V. content.
Radiation: All precautions must be taken to block sources of ionizing radiation likely to cause damage.
Ozone: Storage room shall be free of any equipment that may generate ozone (mercury vapor lamps or high voltage electrical equipment) or combustible gases/vapors.
Deformation: Material shall be stored in a strain-free condition, avoiding stress and other causes of deformation.
Dissimilar Materials: Avoid contact with other materials such as liquids or semi-solids (gasoline, grease, acids, disinfectants, cleaning fluids), metals (copper, manganese, iron), and other elastomers.
|
Order quantity ≤ 3 tons |
The lead-time about 5 working days |
|
Order quantity 5~10tons |
The lead-time about 7-10 days |
|
Full container load |
The lead-time 15-20 days |
|
Packaging |
● 20 kg per carton ● 500 kg per pallet |
|
Transportation |
It can be delivered by truck, train, sea, air. |
We're well-known as one of the leading aem rubber manufacturers and suppliers in China. If you're going to buy good quality aem rubber, welcome to get more information from our factory.
aem rubber, AEM Compound(0/10)
